Click to enlarge
Home » Unmanned System Products » MASS-06 Continuous Echo Simulation Excitation System of Radio Altimeter
MASS-03 Radio Altimeter Continuous Echo Signal Simulator
Back to products
MASS-10 Universal Echo Precision Delay Module (Miniature Universal Continuous Simulation)

MASS-06 Continuous Echo Simulation Excitation System of Radio Altimeter

The MASS-06 Echo Signal Simulation Excitation System, hereinafter referred to as the “Simulation Excitation Source”, is a dedicated equipment designed for the hardware-in-the-loop (HIL) simulation of radio altimeters. It serves as a key component in replicating real-world echo signal scenarios, providing targeted excitation signals that enable the radio altimeter to operate under simulated physical conditions—effectively bridging the gap between theoretical testing and actual operational environments to validate the altimeter’s performance, responsiveness, and reliability.

Categories: , , , ,
Description

Product Description

  • Working center frequency: 4.3ghz;
  • Maximum allowable bandwidth: 200MHz;
  • Maximum allowable input power: 36dbm;
  • Height range: 1-8000m (continuous);
  • Height resolution: 0.5m;
  • Height accuracy: ± (0.2 + 0.005 × h);
  • Correction accuracy after simulated altitude measurement: ± (0.2 + 0.001 × h) m;
  • Height change speed: – 500~500m/S;
  • Height switching time: no more than 1ms;
  • In band fluctuation: no more than 3dB;
  • Maximum attenuation of circuit: not less than 150db (high altitude);
  • Minimum attenuation of loop: no more than 40dB (low altitude);
  • Dynamic range of loop attenuation: not less than 80dB;
  • Dynamic range of loop attenuation: not less than 80dB;
  • Delay line through rejection: not less than 45dB;
  • Pass through rejection of transceiver port: not less than 90dB;
  • Multiple stroke suppression: not less than 45dB;
  • Spurious suppression: not less than 80dB;
  • Phase noise: no more than 80dbc/Hz@1kHz;
  • Control mode: RS422 serial port control;
  • Working temperature: 0 ~ 40 ℃;
  • Storage temperature: – 40 ~ 60 ℃;
  • Working power supply: AC/50Hz/220V, or DC24-36V; power consumption not more than 60W;
  • Volume:433mm×380mm×87mm.

Related products

MY-5001B Radio Altimeter for Sea Condition Identification

The MY-5001B radio altimeter is an all-solid-state C-band device featuring a frequency-modulated continuous wave (FM-CW) system, a constant differential beat frequency, and a closed-loop tracking and measurement mechanism. It ensures a constant beat frequency through servo control of the slope of the sawtooth wave that modulates the microwave oscillator, thereby achieving automatic height tracking. This altimeter incorporates a suite of advanced technologies, including narrowband reception, weighted frequency discrimination, equivalent spectrum leading edge detection, gain PID control, instantaneous sensitivity compensation, temperature compensation, horizon frequency selection design, and power silence. These technologies collectively endow it with advantages such as accurate height measurement, stable tracking, adaptability to various terrains, a wide height measurement range, high precision, and strong anti-interference capabilities.

MDY-01 Radar Seeker

A radar seeker is a radar device installed on missiles, primarily used for target detection and tracking. It provides target position and motion parameters to the missile’s control system, thereby guiding the missile to fly toward the target. The MDY-01 radar seeker is characterized by high measurement accuracy, strong environmental adaptability, and high reliability.

MY-70D Anti Jamming Radio Altimeter

Operating in the C-band, the MY-70D radio altimeter employs a frequency-modulated continuous wave (FMCW) operating system and incorporates closed-loop tracking measurement technology, equipping it with the capability to resist same-frequency asynchronous interference. This ensures that when multiple aircraft take off and fly simultaneously, their altimeters do not interfere with one another. To achieve resistance against active interference, the altimeter adopts a range of measures, including anti-blocking, anti-burnout, power control, beam control, frequency agility, and frequency modulation (FM) technology. Furthermore, it features silent power supply control for its microwave components; its antenna is fitted with a band-pass filter, and a customized radome with frequency-selective functionality is utilized—these design elements enable the altimeter to achieve a wave transmission rate of ≥85% for the operating frequency within the band and less than 10% for out-of-band frequencies, thereby realizing stealth capabilities.

Radio Altimeter MY-3001D

The MY-3001D radio altimeter incorporates two key technologies: a linear modulation coefficient technology that adapts to altitude changes and a narrow-band receiving technology for echo signals, both of which effectively enhance the product’s resistance to active interference. It also adopts coherent local oscillator mixing, granting it superior performance in resisting co-frequency asynchronous interference, and employs echo signal spectrum front-edge detection technology to boost tracking accuracy. In terms of design, the altimeter follows the principles of serialization, standardization, and modularization. While retaining its closed-loop tracking system, it further integrates digital control technology, microwave integration technology, and hybrid integration technology to achieve product modularization. Additionally, it is equipped with a silent function, which further improves the product’s anti-interference capability. This radio altimeter is applicable to cruise missiles and unmanned aerial vehicles (UAVs) for measuring the altitude relative to the sea surface or the ground.

Micro Radio Altimeter MY-2001

The MY-2001 altimeter is a new-generation radar altimeter designed for small missile aircraft; as a compact, full-function radio altimeter that meets aerospace standards, it serves as a key component for longitudinal height channel control and can be widely used in cruise missiles and UAVs to measure altitude relative to the sea or ground. The MY-2001 adopts linear modulation coefficient technology adaptive to height changes and echo signal narrow-band receiving technology to enhance the product’s resistance to active interference, uses coherent local oscillator mixing to achieve superior performance in resisting co-frequency asynchronous interference, employs echo signal spectrum front detection technology to improve tracking accuracy, and follows the three design principles of serialization, standardization, and modularization to ensure good product inheritance; moreover, built on a closed-loop tracking system, it integrates digital control technology, microwave integration technology, and hybrid integration technology to realize product miniaturization.

MAST-11 Equivalent Altitude Simulator of Radio Altimeter

The MAST-11 Equivalent Altitude Simulator of Radio Altimeter is a specialized aerospace testing tool engineered to replicate realistic altitude signals for radio altimeter systems. It generates precise, adjustable equivalent altitude data—mimicking terrain-relative height scenarios—to validate the performance, accuracy, and fault response of on-board radio altimeters during pre-flight testing, maintenance, or system calibration. Compliant with stringent aerospace standards, it ensures reliable simulation of low-to-high altitude ranges, supports interference-free signal output, and integrates easily with aircraft test setups, making it essential for verifying radio altimeter functionality across commercial and military aircraft platforms.

MASS-10 Universal Echo Precision Delay Module (Miniature Universal Continuous Simulation)

The MASS-10 Universal Echo Precision Delay Module, featuring a miniature design and universal continuous simulation capability, is a high-performance component tailored for precise echo signal delay control in radio frequency (RF) testing scenarios. It excels in providing accurate, adjustable delay for echo signals across a wide range of frequencies, making it applicable to various devices like radio altimeters, radars, and other RF-based systems that require reliable echo signal simulation. With its compact size, the module is easy to integrate into limited-space test setups, while the universal continuous simulation function ensures it can replicate diverse real-world signal delay conditions consistently. This module plays a crucial role in verifying the performance of target devices—such as testing their ability to accurately capture and process delayed echo signals—thereby supporting the development, calibration, and quality assurance of RF equipment with high precision and flexibility.

Electronic Countermeasure Radio Altimeter MY-18A、19A

Developed to meet the requirements of electronic countermeasures and terminal penetration, the MY-18A and MY-19A electronic countermeasure radio altimeters incorporate a range of advanced technologies including frequency agility, radiated power control, beam control, anti-burnout, anti-blocking, and echo frequency-domain processing—endowing them with excellent anti-jamming performance. Meanwhile, these altimeters also integrate a sea state identification function, which leverages information such as echo spectrum broadening, Doppler frequency, and altitude under different sea conditions to achieve accurate sea state recognition.